Polymer Nation F-41 SLQ Clear UV Resistant Epoxy Slurry Quartz

F-41 SLQ Packaging: 1 mix kit consists of 2 gal A, 1 gal B, 1-50 LB. bag of PN 1321 F (see color chart below)

Color Chart

Polymer Nation F-41 SLQ is primarily used to create an inexpensive, decorative and durable floor finish.

 

Categories: ,

Description

Polymer Nation F-41 SLQ consist of our clear, UV resistant epoxy and proprietary ultra-fine color quartz blends to create a 1/16″ decorative floor finish. This mixture allows the installer to blend 8 custom colors to create a unique floor finish. When PN 1321 Glint is added to the mix, the finish comes alive with light reflectivity. The cured material has high compressive strength (three times that of concrete) , great impact resistance and can be finish-coated with various epoxy and polyaspartic topcoats.

Description Results Notes
Number of mixes per kit 1 A 1 mix kit consists of 2 gal A, 1 gal B, 1-50 LB. bag of PN 1321 F.
Number of Components 3
Mix Ratio Liquids by Volume 2:1 It is always preferred to mix the entire kit, whenever possible, to avoid off-ratio mixtures
Ideal Application Temperatures 60F-90F Verify that substrate temperature is above 5 degrees of dewpoint during application and cure of material to avoid a potential amine blush
Mixed Viscosity in cP@25C/77F 600-700 Warmer temperatures will reduce viscosity and lower temperatures will increase viscosity
Gel Time 60 min. Warmer temperatures will decrease gel time and lower temperatures will increase gel time
Dry to Touch 5-6 Hours Warmer temperatures will reduce time and colder temperatures will increase time
Through Dry 10-12 Hours Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Walk 15 Hours Warmer temperatures will reduce time and colder temperatures will increase time
Dry to Lightly Use 24 Hours Warmer temperatures will reduce time and colder temperatures will increase time
Full Cure 7 Days Warmer temperatures will reduce time and colder temperatures will increase time
Shore Hardness at 24 hours D65 Warmer temperatures will increase hardness
Shore Hardness at 7 days D78 Warmer temperatures will shorten time to reach full hardness
Gloss @ 60 Degree Angle 90+ Not top coated.  See Gloss data for selected top coat if required
VOC’s of Mixed Material <50g/L EPA Method 24
Color Scale per ASTM D1500 .5-1.0 Clear to slightly amber
Solids by Volume Mixed 100%
Storage 60F-90F Store material between 60-90 degrees F in a protected dry location.
Odor Subtle
Coverage Per Mix Each mix will cover 155 sq. ft. at 1/16″ theoretical coverage. A waste factor of 10% should be contemplated
Disposal Dispose of  material, containers, solvents, etc.per Federal, State and local guideline, rules and laws
Available Colors System color is generated by the combination of aggregate blends.
Mixing & Installation A mixture consists of 2 gal A, 1 gal B and 50 LB. of C (PN 1321 F). Combine part A and B into a single container, large enough to accept the entire kit (1 mix equals 6.5 gallons when Part C is added). Premix liquids at 350 RPM for 1 minutes. Pour Part C (PN 1321 F) into the mixed resin and continue mixing until a homogenous slurry is achieved (2-3 minutes usually), making sure not to introduce excessive air into the solution. Pour material on to floor and spread to desired thickness using a screed rake or notched squeegee. Once material has leveled, back roll with a spiked roller to aid in the release of trapped air. Whenever possible, work the shorter distance not the longer as this will help keep a fresh edge and make for easier blending. Temperature should be descending , not ascending during application and cure of slurry. This is critical whenever a broadcast will not be cast into the wet slurry. Recoat within 24 hours. Clean tools with a solvent similar to Xylene or Acetone.
Polymer Nation believes the information contained herein to be true and accurate. Information contained herein is for evaluation purposes only.